Request a demo
Land and surveyComing soon

Survey data, site and roadway design, and construction staking.

Section through a bridge replacement project An engineering section of a two-span bridge over a channel, numbered by project stage: 1 survey and alignment, 2 borings and drilled shaft foundations, 3 girders, pier and abutments, 4 specification notes, 5 construction schedule, 6 material tests on the embankment fill and concrete, 7 inspection of bearings and girders. B-1 B-2 10+00 11+00 12+00 13+00 14+00 15+00 16+00 NOTES1. Drilled shafts: Section F-210.2. Bi-directional load test: Section F-430. SCHEDULE SECTION A-ABridge replacement, two spans Survey and alignment 1 Borings and foundations 2 Structure 3 Specifications 4 Construction schedule 5 Material tests 6 Inspection 7

Landtechware modules

Survey data, site and roadway design, and construction staking. Open a module to see its scope and standards.

Data

Survey

  • Traverse and ClosureField traverse adjustmentComing soon

    Adjusts closed and open field traverses by compass rule or least squares from measured angles and distances. Reports angular misclosure, linear misclosure and precision ratio, and produces adjusted coordinates for each traverse point.

    Standards
    No single governing document
    Uses
    Field angles, distances and control points
    Provides
    Adjusted control coordinates and closure report
  • Boundary and PlatProperty linesComing soon

    Computes property lines, lot corners, bearings, distances and curve data from deed calls and located monuments. Produces boundary closures, parcel areas, legal descriptions and plat drawing data for review and recording.

    Standards
    ALTA/NSPS Minimum Standard Detail Requirements for Land Title Surveys, BLM Manual of Surveying Instructions, LandXML
    Uses
    Adjusted control and located monuments
    Provides
    Boundary lines, parcels and legal descriptions
  • Topographic SurfaceGround modelsComing soon

    Builds triangulated ground surface models from survey points, breaklines and surface boundaries for the project site. Produces contours, spot elevations and surface files that grading, drainage and geotechnical work use for existing ground.

    Standards
    ASPRS Positional Accuracy Standards for Digital Geospatial Data, LandXML
    Uses
    Survey points, breaklines and control
    Provides
    Existing ground surface and contours

Design

Site and roadway design

  • Grading and EarthworkPads and volumesComing soon

    Designs building pads, slopes and finished grade surfaces against the existing ground model. Computes cut and fill volumes by surface comparison or average end area and reports quantities with shrink and swell factors.

    Standards
    LandXML
    Uses
    Existing ground surface and boring locations
    Provides
    Finished grade surface and earthwork volumes
  • StormwaterRunoff and detentionComing soon

    Computes runoff from drainage areas, land cover and soil groups, and routes hydrographs through detention ponds and outlet structures. Produces peak flows, pond stage and storage tables, and storm sewer sizing summaries.

    Standards
    NRCS TR-55, NRCS TR-20, FHWA HEC-22 Urban Drainage Design Manual, FDOT Drainage Manual
    Uses
    Surfaces, drainage areas and soil groups
    Provides
    Runoff, pond routing and pipe sizes
  • Roadway GeometryAlignments and profilesComing soon

    Lays out horizontal alignments with tangents, circular and spiral curves, and vertical profiles with grades and vertical curves. Produces stationing, curve data, superelevation and design speed checks for plan and profile sheets.

    Standards
    AASHTO A Policy on Geometric Design of Highways and Streets, FDOT Design Manual, LandXML
    Uses
    Existing ground surface and right of way
    Provides
    Alignments, profiles and station offsets
  • Subdivision LayoutLots and easementsComing soon

    Divides parcels into lots, blocks, rights of way and easements against the boundary and setback requirements. Computes lot areas, frontages and closures, and produces lot and easement data for the plat.

    Standards
    LandXML
    Uses
    Boundary, surfaces and alignments
    Provides
    Lots, easements and rights of way

Construction

Layout

  • Construction StakingStakeout and cut sheetsComing soon

    Computes stakeout points, offsets and grades from design alignments, surfaces and control. Produces cut sheets and stakeout files for field crews, and records staked positions with their differences from design.

    Standards
    LandXML
    Uses
    Alignments, design surfaces and control
    Provides
    Stakeout points and cut sheets

Questions about Landtechware?