Request a demo
Materials testingComing soon

Field and laboratory tests on soil, concrete, asphalt and steel, checked against the specification and recorded for acceptance.

Section through a bridge replacement project An engineering section of a two-span bridge over a channel, numbered by project stage: 1 survey and alignment, 2 borings and drilled shaft foundations, 3 girders, pier and abutments, 4 specification notes, 5 construction schedule, 6 material tests on the embankment fill and concrete, 7 inspection of bearings and girders. B-1 B-2 10+00 11+00 12+00 13+00 14+00 15+00 16+00 NOTES1. Drilled shafts: Section F-210.2. Bi-directional load test: Section F-430. SCHEDULE SECTION A-ABridge replacement, two spans Survey and alignment 1 Borings and foundations 2 Structure 3 Specifications 4 Construction schedule 5 Material tests 6 Inspection 7

Labtechware modules

Field and laboratory tests on soil, concrete, asphalt and steel, checked against the specification and recorded for acceptance. Open a module to see its scope and standards.

Testing

Field tests

  • Soil DensityNuclear gauge and proctor comparisonComing soon

    Records in-place density and moisture content from nuclear gauge tests by lift and location. Compares results with the maximum dry density and optimum moisture from the proctor test, and reports percent compaction against the specified minimum.

    Standards
    ASTM D6938, AASHTO T 310, AASHTO T 99, AASHTO T 180
    Uses
    Proctor results, specification limits
    Provides
    Compaction results with pass or fail
  • Concrete Field TestsSlump, air, temperature and cylindersComing soon

    Records slump, air content, concrete temperature and unit weight for each load sampled, with cylinder sets cast. Checks each result against the mix design and specification limits, and tracks cylinder sets for laboratory testing.

    Standards
    ASTM C143, ASTM C231, ASTM C1064, ASTM C31
    Uses
    Mix designs, placement locations
    Provides
    Fresh concrete results and cylinder sets
  • Asphalt DensityCores and gauge readingsComing soon

    Records core bulk specific gravity and nuclear gauge readings for asphalt lots and sublots. Computes in-place density as percent of maximum specific gravity and checks results against the specified density limits for each lot.

    Standards
    AASHTO T 166, AASHTO T 209, AASHTO T 355
    Uses
    Mix designs, paving lots
    Provides
    Lot density results with pass or fail

Laboratory

  • Concrete StrengthCylinder and core breaksComing soon

    Records compressive strength of cylinders and cores by set, age and placement. Checks individual and running average results against the specified strength, and reports strength results to acceptance and pay item records for the placement.

    Standards
    ASTM C39, ASTM C42, ACI 318
    Uses
    Cylinder sets, mix designs, specified strength
    Provides
    Strength results with acceptance status
  • Soil LaboratoryClassification, proctor, gradationComing soon

    Records laboratory test results for soil classification, Atterberg limits, gradation, moisture content and proctor tests. Classifies each sample, plots gradation and moisture-density curves, and makes results available to design and field density checks.

    Standards
    ASTM D2487, ASTM D4318, ASTM D6913, ASTM D698
    Uses
    Sample locations, project borings
    Provides
    Classification, gradation and proctor results
  • Concrete MaturityStrength by maturityComing soon

    Estimates in-place concrete strength from temperature history using a strength-maturity relationship calibrated for the mix. Computes maturity index with time from embedded loggers and reports the time at which the required strength is reached.

    Standards
    ASTM C1074
    Uses
    Mix design, temperature logger data
    Provides
    Estimated in-place strength with time

Construction

Acceptance

  • Sources and Mix DesignsApproved sources and mix designsComing soon

    Records approved material sources and mix designs with their properties and approval dates. Provides the target values and tolerances that field and laboratory tests are checked against, and links each placement to its approved mix.

    Standards
    FDOT Standard Specifications for Road and Bridge Construction
    Uses
    Submittals, specification sections
    Provides
    Approved sources and mix targets
  • Material AcceptanceTests and certifications checked against the specificationComing soon

    Checks test results and material certifications against the specification requirements for each material and lot. Produces acceptance status by lot, sampling frequency compliance, and results for pay item quantities and adjustments.

    Standards
    23 CFR 637, FDOT Standard Specifications for Road and Bridge Construction
    Uses
    Test results, certifications, specifications
    Provides
    Acceptance status by lot
  • NonconformanceFailed tests, evaluation and resolutionComing soon

    Records failed tests and nonconforming material with location, quantity and the governing requirement. Tracks evaluation, disposition, retesting and resolution, and reports open items and any resulting removal or pay adjustment.

    Standards
    No single governing document
    Uses
    Failed tests, acceptance records
    Provides
    Nonconformance status and disposition

Questions about Labtechware?